计算机网络-ensp实现VPN

实验过程：

1、建立如图拓扑结构

网络拓扑图

2、为主机配置地址

R1接口配置

sys

sysn R1

int g0/0/0

ip add 192.168.12.3 24

int g0/0/1

ip add 192.168.1.254 24

undo shu

#

R2接口配置

sys

sysn R2

int g0/0/0

ip add 192.168.12.2 24

int g0/0/1

ip add 192.168.23.1 24

undo shu

#

R3接口配置

sys

sysn R3

int g0/0/0

ip add 192.168.2.254 24

int g0/0/1

ip add 192.168.23.3 24

undo shu

#

然后配置VPN

 

公司总部路由器R3配置：

[R3]acl number 3000 //创建ACl

[R3-acl-adv-3000]rule 5 permit ip source 192.168.2.0 0.0.0.255 destination 192.168.1.0 0.0.0.255 //配置允许192.168.2.0 网段访问192.168.1.0网段

[R3-acl-adv-3000]ipsec proposal huawei //新建安全提议，名字为huawei

[R3-ipsec-proposal-huawei]esp authentication-algorithm sha1 //设置加密方式sha1，默认MD5

[R3-ipsec-proposal-huawei]q

[R3]ipsec policy huawei 10 manual

//配置ipsec策略，策略名为huawei，编号为10，模式为手动配置模式

[R3-ipsec-policy-manual-huawei-10]security acl 3000

//匹配acl，就是让这个数据（192.168.1.0访问192.168.2.0的数据）走VPN

[
R3-ipsec-policy-manual-huawei-10]proposal huawei //引用名为huawei的提议

[
R3-ipsec-policy-manual-huawei-10]tunnel local 192.168.23.3 //本地隧道地址

[
R3-ipsec-policy-manual-huawei-10]tunnel remote 192.168.12.3 //对端隧道地址

[R3-ipsec-policy-manual-huawei-10]sa spi inbound esp 54321

//安全联盟入方向，SPI为54321，本端入方向SPI必须和对端出方向SPI一致

[
R3-ipsec-policy-manual-huawei-10]sa string-key inbound esp cipher huawei //安全联盟密钥，入方向为加密的huawei，本端入方向密钥必须和对端出方向密钥一致

[R3-ipsec-policy-manual-huawei-10]sa spi outbound esp 12345

//安全联盟出方向，SPI为12345，本端出方向SPI必须和对端入方向SPI一致

[R3-ipsec-policy-manual-huawei-10]sa string-key outbound esp cipher huawei000

//安全联盟密钥，出方向为加密的huawei，本端入方向密钥必须和对端出方向密钥一致

[R3]int g0/0/1 //进入端口g0/0/1

[R3-GigabitEthe.NET0/0/1]ipsec policy huawei //在端口上应用

在R3上配置静态路由

[R3]ip route-static 0.0.0.0 0 192.168.23.1

 

分公司路由器R1配置：

[R1]acl number 3000

[R1-acl-adv-3000]rule 5 permit ip source 192.168.1.0 0.0.0.255 destination 192.1

68.2.0 0.0.0.255

[R1-acl-adv-3000]ipsec proposal huawei

[R1-ipsec-proposal-huawei]esp authentication-algorithm sha1

[R1-ipsec-proposal-huawei]q

[R1]ipsec policy huawei 10 manual

[R1-ipsec-policy-manual-huawei-10]security acl 3000

[R1-ipsec-policy-manual-huawei-10]proposal huawei

[R1-ipsec-policy-manual-huawei-10]tunnel local 192.168.12.3

[R1-ipsec-policy-manual-huawei-10]tunnel remote 192.168.23.3

[R1-ipsec-policy-manual-huawei-10]sa spi inbound esp 12345

[R1-ipsec-policy-manual-huawei-10]sa string-key inbound esp cipher huawei000

[R1-ipsec-policy-manual-huawei-10]sa spi outbound esp 54321

[R1-ipsec-policy-manual-huawei-10]sa string-key outbound esp cipher huawei

[R1]int g0/0/0

[R1-GigabitEthernet0/0/0]ipsec policy huawei

 

在R1上配置静态路由

[R1]ip route-static 0.0.0.0 0 192.168.12.2

最终效果：PC1ping通PC2

 

最终效果：PC2pingPC1

 

 

 

在R1的g0/0/0接口抓包

 

 

在R3的g0/0/1接口抓包